Transport GX21
B2735
1
2
3
1
2
3
RST
User’s Manual
Document part number: D1577-100
Federal Communications Commission
Notice for the USA Compliance Information State-
ment (Declaration of Conformity Procedure) DoC
FCC Part 15: This device complies with part 15 of the
FCC Rules
Operation is subject to the following conditions:
1) This device may not cause harmful interference, and
2) This device must accept any interference received including inter-
ference that may cause undesired operation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try one or more of the following measures:
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the
receiver.
•
Plug the equipment into an outlet on a circuit different from
that of the receiver.
Consult the dealer on an experienced radio/television technician for
help.
Notice for Canada
This apparatus complies with the Class B limits for radio interfer-
ence as specified in the Canadian Department of Communications
Radio Interference Regulations. (Cet appareil est conforme aux
norms de Classe B d’interference radio tel que specifie par le Minis-
tere Canadien des Communications dans les reglements d’inetefer-
ence radio.)
Notice for Europe (CE Mark) This product is in conformity
with the Council Directive 89/336/EEC, 92/31/EEC
(EMC).
CAUTION: Lithium battery included with this board. Do not puncture,
mutilate, or dispose of battery in fire. Danger of explosion if battery
is incorrectly replaced. Replace only with the same or equivalent
type recommended by manufacturer. Dispose of used battery
according to manufacturer instructions and in accordance with your
local regulations.
ii
About this manual
This manual provides you with instructions on installing your Trans-
port GX21 (B2735), and consists of the following sections
Chapter 1:
Provides an introduction to the Transport GX21 (B2735) bare bones,
packing list, describes the external components, gives tables of key
components, and provides block diagrams of the system.
Chapter 2:
Covers procedures on installing the CPUs, memory modules,
optional PCI card, and hard drives.
Chapter 3:
Covers removal and replacement procedures for pre-installed com-
ponents.
Appendix:
Provides detailed specifications, maintenance and troubleshooting
procedures, an explanation of BIOS and technical diagrams.
iii
Safety information
Before installing and using the Transport GX21 , take note of the fol-
lowing precautions:
•
•
•
Read all instructions carefully.
Do not place the unit on an unstable surface, cart or stand.
Do not block the slots or openings on the unit which are
provided for ventilation.
•
•
Only use the power source indicated on the marking label.
If you are not sure, contact the power company.
The unit uses a three-wire grounded cable, which is sup-
plied with a third pin to ground the unit and prevent electric
shock. Do not defeat the purpose of this pin. If your outlet
does not support this type of plug, contact an electrician to
replace the obsolete outlet.
•
•
•
Do not place anything on the power cord. Place the power
cord where it will not be stepped on.
Follow all warnings and cautions in this manual and on the
unit case.
Do not push objects in the ventilation slots as they may
touch high voltage components and result in shock and
damage to the components.
•
•
When replacing parts, ensure that you use parts specified
by the manufacturer.
When service or repairs have been carried out, perform
routine safety checks to verify that the system is operating
correctly.
•
•
Avoid using the system near water, in direct sunlight, or
near a heating device.
Cover the unit when not in use.
iv
Table of Contents
Overview
About the Transport GX21 (B2735) ................................................... 1
Product models.................................................................................... 1
Features ............................................................................................... 2
B2735G21S2 specifications............................................................. 2
B2735G21S4H specifications.......................................................... 3
B2735G21U4H specifications......................................................... 4
Unpacking ........................................................................................... 5
Box contents .................................................................................... 5
Accessories ...................................................................................... 7
Opening the box............................................................................... 8
About the product................................................................................ 9
System front view and front panel................................................... 9
System rear view.............................................................................. 10
System internal views...................................................................... 11
Setting up
Before you begin................................................................................. 15
Work area......................................................................................... 15
Tools ................................................................................................ 15
Precautions....................................................................................... 16
Installing motherboard components.................................................... 17
Removing the chassis cover............................................................. 17
Installing CPUs................................................................................ 18
Installing memory............................................................................ 20
Installing a PCI card ........................................................................ 21
Installing a hard drive.......................................................................... 25
Installing internal hard drives (B2735G21S2)................................. 25
Installing an IDE hard drive..................................................... 25
Installing an internal S-ATA hard drive .................................. 27
Installing an external S-ATA hard drive (B2735G21S4H) ............. 30
Installing an external SCSI hard drive (B2735G21U4H)................ 31
Rack mounting .................................................................................... 34
Replacing pre-installed components
Introduction......................................................................................... 39
Replacing motherboard components................................................... 39
Disconnecting all motherboard cables............................................. 39
Replacing the motherboard.............................................................. 42
Replacing the CD-ROM drive ............................................................ 43
Replacing the slim CD-ROM drive (B2735G21S2)........................ 43
Replacing the CD-ROM drive (B2735G21U4H/B2735G21S4H) .. 45
Replacing the floppy disk drive .......................................................... 47
Replacing the floppy disk drive (B2735G21S2).............................. 47
Replacing the floppy disk drive (B2735G21S4H/B2735G21U4H). 48
Replacing the LED control board ....................................................... 49
Replacing the storage backplane......................................................... 50
S-ATA backplane (B2735G21S4H)................................................ 50
Replacing the S-ATA backplane (B2735G21S4H)................ 50
S-ATA backplane features....................................................... 52
SCSI backplane (B2735G21U4H)................................................... 53
Replacing the SCSI backplane (B2735G21U4H).................... 53
SCSI backplane features .......................................................... 55
Replacing the power supply................................................................ 56
Replacing the cooling fans.................................................................. 57
Cooling fan connections .................................................................. 59
Appendix
BIOS.................................................................................................... 61
Introduction...................................................................................... 61
BIOS setup utility ............................................................................ 61
BIOS menu bar ................................................................................ 63
BIOS legend bar............................................................................... 64
BIOS main menu ............................................................................. 65
BIOS advanced menu ...................................................................... 66
CPU configuration submenu............................................................ 67
IDE configuration submenu............................................................. 69
S-ATA Port/Primary IDE/Secondary IDE configuration submenu. 71
Floppy configuration submenu........................................................ 72
Super I/O configuration submenu.................................................... 73
ACPI settings submenu.................................................................... 74
Advanced ACPI configuration submenu......................................... 76
DMI event logging submenu ........................................................... 78
Remote access configuration submenu............................................ 79
USB configuration menu ................................................................. 80
USB mass storage device configuration submenu........................... 82
Onboard devices configuration submenu ........................................ 83
Hardware monitor submenu............................................................. 84
Advanced PCI/PnP menu................................................................. 86
BIOS boot settings menu................................................................. 88
Boot Settings configuration submenu.............................................. 89
Boot device priority submenu.......................................................... 91
Hard disk submenu .......................................................................... 93
Removable drives submenu............................................................. 94
ATAPI CD-ROM drives submenu .................................................. 95
BIOS security menu......................................................................... 96
BIOS chipset settings....................................................................... 98
Northbridge chipset configuration submenu.................................... 99
Southbridge chipset configuration submenu.................................... 100
Intel PCI-64 Hub 2 configuration submenu..................................... 101
BIOS exit menu ............................................................................... 102
SCSI and S-ATA controller cards....................................................... 104
Controller card location ................................................................... 104
M7902 Ultra 320 SCSI controller card features.............................. 105
M8110 S-ATA RAID controller card features ................................ 106
Technical support................................................................................ 107
Help resources: ................................................................................ 107
Returning merchandise for service .................................................. 107
1.1 About the Transport GX21 (B2735)
Chapter 1: Overview
1.1
About the Transport GX21 (B2735)
Congratulations on your purchase of the Transport GX21
(B2735), rack mountable, barebone system for Intel® Xeon™
processor. The Transport GX21 (B2735) uses an advanced
Intel chipset for optimum performance and reliability. Add-on
S-ATA or SCSI storage controllers provide great flexibility
and combine with Gigabit Ethernet ports to provide powerful
computing capacity and optimal I/O bandwidth for the most
demanding of enterprises.
The rugged, industry standard 19-inch, rack mountable
design contains up to 4 HDD bays, 1 slim CD-ROM bay and 1
3.5-inch FDD, making it both flexible and practical.
1.2
Product models
Table 1: Transport GX21 (B2735) models
Hot
Swap
Support
HDD
Back-
plane
Model
HDD
SKU TYpe
B2735G21S2
B2735G21S4H
B2735G21U4H
2 internal
HDD bays
No
NA
Standard SKU
OEM Only
4 removable
HDD bays
Yes
Yes
4 port
S-ATA
4 removable
HDD bays
4 port
SCSI
OEM Only
Chapter 1: Overview
1
1.3 Features
1.3
Features
1.3.1 B2735G21S2 specifications
Enclosure Storage
•
•
Industry standard, 19” rack mount-
able, 1U chassis
•
•
Integrated dual channel IDE con-
troller from ICH5R
2 internal access 1” HDD bays, 1
slim CD-ROM bay, 1 bay for 3.5”
FDD or internal access 1” HDD
21.5 x 17 x 1.7 inch (547 x 432 x
43 mm)
2 Integrated S-ATA ports from
ICH5R (RAID 0,1 support)
2 Internal (fixed) HDD bays
Slim 24x CD-ROM drive
Optional 3.5 inch FDD
•
•
•
•
Processors
Cooling
•
•
Dual mPGA604 socket
•
•
•
•
5 cooling fans(40 x 40 x 28 mm)
1 power supply fan
2 CPU heatsinks
Hardware auto fan speed control
Single or dual Intel® Xeon™ pro-
cessor with 512K iL2 and 1 MB iL3
533/400 MHz FSB
•
Chipset
Motherboard
•
•
•
Intel® E7501 server chipset
•
Tyan Tiger S2735G3NR-8M moth-
erboard
ATX form factor
Award BIOS 8.0 on 8 Mb LPC
flash ROM
MCH + ICH5R + P64H2 + FWH
Winbond W83627HF super I/O
chip
analog device ADM 1027 hard-
ware monitoring IC
•
•
•
•
LAN remote boot (PXE) support
and SMBIOS v2.3
Memory
Networking
•
•
•
•
128-bit dual channel memory bus
6 DDR DIMM sockets
Up to 12 GB DDR266/200SDRAM
Support for registered ECC type
memory modules
•
2 Gigabit Ethernet ports (Intel®
82546EB LAN controller)
1 10/100 Mbps LAN port (Intel®
82551QM controller)
•
Expansion slots
Power supply
•
(1) 64-bit/133 MHz PCI-X slot on
•
EPS 12V, 1U, 400W with PFC
riser card
Back I/O ports
Video
•
Stacked PS/2 mouse and key-
•
ATI® Rage™ XL PCI Graphics
board ports
controller
•
•
•
•
2 USB 2.0 ports
1 9-pin UART serial port
3 RJ-45 LAN ports
1 VGA port
•
8 MB frame buffer video memory
Front panel
Regulatory
•
2 USB 2.0 ports
•
FCC class B (declaration of
•
IDE activity, LAN activity, and
power LEDs
conformity)
CE (declaration of conformity)
•
•
Power and reset switches
2
Chapter 1: Overview
1.3 Features
1.3.2 B2735G21S4H specifications
Enclosure
Storage
•
•
•
Industry standard, 19” rack mount-
able, 1U chassis
4 external access HDD bays, 1
slim CD-ROM bay, 1 slim FDD bay
21.5 x 17 x 1.7 inch (547 x 432 x
43 mm)
•
Integrated dual channel IDE con-
troller from ICH5R
•
Tyan M8110 4-port S-ATA RAID
card (RAID 0,1, 0+1)
4 hot-swap S-ATA HDD bays
Slim 24x CD-ROM drive
Slim FDD
•
•
•
Processors
Cooling
•
•
Dual mPGA604 socket
•
•
•
•
5 cooling fans (40 x 40 x 28 mm)
1 power supply fan
2 CPU heatsinks
Hardware auto fan speed control
Single or dual Intel® Xeon™ pro-
cessor with 512K iL2 and 1 MB iL3
533/400 MHz FSB
•
Chipset
Motherboard
•
•
•
Intel® E7501 server chipset
•
Tyan Tiger S2735G3NR-8M moth-
erboard
ATX form factor
Award BIOS 8.0 on 8 Mb LPC
flash ROM
MCH + ICH5R + P64H2 + FWH
Winbond W83627HF super I/O
chip
analog device ADM 1027 hard-
ware monitoring IC
•
•
•
•
LAN remote boot (PXE) support
and SMBIOS v2.3
Memory
Networking
•
•
•
•
128-bit dual channel memory bus
6 DDR DIMM sockets
Up to 12 GB DDR266/200SDRAM
Support for registered ECC type
memory modules
•
2 Gigabit Ethernet ports (Intel®
82546EB LAN controller)
1 10/100 Mbps LAN port (Intel®
82551QM controller)
•
Expansion slots
Power supply
•
(1) 64-bit/133 MHz PCI-X slot on
•
EPS 12V, 1U, 400W with PFC
riser card
Back I/O ports
Video
•
Stacked PS/2 mouse and key-
•
ATI® Rage™ XL PCI Graphics
board ports
controller
•
•
•
•
2 USB 2.0 ports
1 9-pin UART serial port
3 RJ-45 LAN ports
1 VGA port
•
8 MB frame buffer video memory
Front panel
Regulatory
•
2 USB 2.0 ports
•
FCC class B (declaration
•
HDD activity, LAN activity, power,
fan fail and temperature fail LEDs
Power and reset switches
conformity)
CE (declaration of conformity)
•
•
Chapter 1: Overview
3
1.3 Features
1.3.3 B2735G21U4H specifications
Enclosure
Storage
•
•
•
Industry standard, 19” rack mount-
able, 1U chassis
4 external access HDD bays, 1
slim CD-ROM bay, 1 slim FDD bay
21.5 x 17 x 1.7 inch (547 x 432 x
43 mm)
•
•
•
Integrated dual channel IDE con-
troller from ICH5R
Tyan M702 dual channel Ultra 320
SCSI card (HostRAID support)
4 hot-swap, Ultra320 SCSI HDD
bays
•
•
Slim 24x CD-ROM drive
Slim FDD
Processors
Cooling
•
•
Dual mPGA604 socket
•
•
•
•
5 cooling fans (40 x 40 x 28 mm)
1 power supply fan
2 CPU heatsinks
Hardware auto fan speed control
Single or dual Intel® Xeon™ pro-
cessor with 512K iL2 and 1 MB iL3
533/400 MHz FSB
•
Chipset
Motherboard
•
•
•
Intel® E7501 server chipset
•
Tyan Tiger S2735G3NR-8M moth-
erboard
ATX form factor
Award BIOS 8.0 on 8 Mb LPC
flash ROM
MCH + ICH5R + P64H2 + FWH
Winbond W83627HF super I/O
chip
analog device ADM 1027 hard-
ware monitoring IC
•
•
•
•
LAN remote boot (PXE) support
and SMBIOS v2.3
Memory
Networking
•
•
•
•
128-bit dual channel memory bus
6 DDR DIMM sockets
Up to 12 GB DDR266/200SDRAM
Support for registered ECC type
memory modules
•
2 Gigabit Ethernet ports (Intel®
82546EB LAN controller)
1 10/100 Mbps LAN port (Intel®
82551QM controller)
•
Expansion slots
Power supply
•
(1) 64-bit/133 MHz PCI-X slot on
•
EPS 12V, 1U, 400W with PFC
riser card
Back I/O ports
Video
•
Stacked PS/2 mouse and key-
•
ATI® Rage™ XL PCI Graphics
board ports
controller
•
•
•
•
2 USB 2.0 ports
1 9-pin UART serial port
3 RJ-45 LAN ports
1 VGA port
•
8 MB frame buffer video memory
Front panel
Regulatory
•
2 USB 2.0 ports
•
FCC class B (declaration
•
HDD activity, LAN activity, power,
fan fail and temperature fail LEDs
Power and reset switches
conformity)
CE (declaration of conformity)
•
•
4
Chapter 1: Overview
1.4 Unpacking
1.4
Unpacking
1.4.1 Box contents
B2735
G21S2
B2735
G21S4H
B2735
G21U4H
Component
Description
1 U chassis, 2
internal HDD
bays
Yes
1
2
3
1
2
RST
P/N 541273080001
1U chassis, 4
external HDD
bays
Yes
Yes
Yes
Yes
1
2
3
1
2
3
RST
P/N 541273080002
P/N 541172850002
Tyan S2735
system board
(pre-installed)
Yes
Tyan M8110 S-
ATA RAID con-
troller card
Yes
(pre-installed)
P/N 541172850002
Tyan M7902
Yes
Ultra 320 SCSI
controller card
(pre-installed)
P/N 541190860001
2
40
94V-0
J1
Slim CD-ROM
adapter
Yes
Yes
Yes
Yes
Yes
Yes
39
1
4
J3
1
1 CORER1.PCB MADE
J4
TAIWAN
P/N 340729700001
24x slim CD-
ROM drive
(pre-installed)
P/N 523430061006
2
40
94V-0
J1
Slim FDD
adapter
Yes
Yes
Yes
Yes
39
1
4
J3
1
1 CORER1.PCB MADE
J4
TAIWAN
P/N 344723200001
P/N 523410290033
Chapter 1: Overview
Slim floppy
disk drive (pre-
installed)
5
1.4 Unpacking
Box contents (cont.)
B2735
G21S2
B2735
G21S4H
B2735
G21U4H
Component
Description
S-ATA back-
plane and
Yes
ON
1
KE
2
3
4
5
6
holdingbracket
(pre-installed)
P/N 412223700099
P/N 523410290033
4-port Ultra
320 SCSI
backplane
(pre-installed)
Yes
LED control
board (pre-
installed)
Yes
Yes
Yes
Yes
Yes
P/N 412223700102
P/N 412223700109
64-bit riser
card (pre-
installed)
Yes
Yes
ATX 12V
Yes
Yes
400W PSU
(pre-installed)
P/N 471172400038
P/N 336252012099
15,500 rpm
cooling fan (2
pcs per sys-
tem)
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
11,500 rpm
cooling fan (3
pcs per sys-
tem)
P/N 336252012101
P/N 342730800002
Fan holding
bar
6
Chapter 1: Overview
|